How to make a crossbow for spearfishing?

Crossbow for spearfishing - extremelyclaimed weapons in the midst of avid fishermen. This means of fishing is distinguished above all by the high accuracy of firing and the reliability of the design. The best crossbows for underwater hunting always look preferable along with the same pneumatic guns due to the special ease of operation.

crossbow for spearfishing

Principle of operation

By design, a crossbow gun for underwater huntingpractically does not differ from its land "fellows". As a matter of fact, the adaptation is presented in the form of the case with a hollow under an arrow and the stretched drafts. The latter are held in a charged position by a special harpoon, which is fixed by means of trigger elements. Pressing the trigger leads to the release of the rods, which give the boom the necessary acceleration.

crossbow for underwater hunting with their own hands

Type of barrel

The crossbow for underwater hunting contains the head part, which can be represented in such variants:

  1. Open - offers the hunter a better visibility and is characterized by increased power.
  2. Closed - stands out among other solutions improved accuracy, which is provided by the presence of twin rods.
  3. With one thrust, it is a good choice for hunters who are ready to sacrifice precision for maximum power.
  4. Mixed - it uses a specific,annular steam traction, which makes it possible to increase the power of the weapon without compromising accuracy. Such a head part is best suited for the production of large fish.
  5. Hydroformed barrel - allows you to get a perfectly smooth, verified shot trajectory to perform the most accurate shooting.

With regard to traction, they come in different thicknessesand length. For hunting relatively small fish it is advisable to use crossbows, where the head part is completed with thin thrusts. To produce a large "catch" fit the thickest thrust.

gun crossbow for spearfishing

Benefits

Among the advantages of crossbows for underwater hunting is worth noting the following:

  • minimum swing of the weapon during the shot, which affects the increase in accuracy;
  • simplicity of design;
  • affordable cost;
  • When operating, there is no need to use additional accessories, for example, a pump, which acts as an obligatory means for charging pneumatics;
  • noiseless shooting.

disadvantages

The obvious drawbacks of the crossbowfor underwater hunting, they are: increased probability of damage to the released boom, impressive dimensions of the structure. In addition, the user does not have the ability to regulate the force of fire, and the combat power is reduced by an order of magnitude in comparison with pneumatic rifles.

best crossbows for spearfishing

Crossbow for underwater hunting with their own hands

Begin your own handmade weapons forUnderwater fishing should be done by searching for a suitable spring. The diameter of the turns of the latter should be of the order of 12-15 mm, and the pitch - not less than 2 mm. It is necessary to take into account the fact that the springs work on compression. Therefore, the length of this element should exceed the dimensions of the body of the self-made crossbow by approximately 100-200 mm. Consider possible shrinkage of the spring as the weapon is used.

With regard to the parameters of the trunk, the most convenientfor hunting in most water bodies, the length will be about 60-75 cm. Any lightweight tube with side openings for the unimpeded exit of water is suitable for the role of this structural element. In this trunk a notch under the sear is cut. A blanking plug and a muffler are also made of metal. Towards the latter will then be attached traction.

To make a full crossbow forunderwater hunting with their own hands, will require the preparation of a comfortable grip and an effective trigger mechanism. The body and handle can be cut from wood or metal plates. The finished structure is connected to the stem part by bolts.

To complete a crossbow for diving,it is required to install a trigger that consists of a trigger, a sear, a spring and a fuse. Preparation of these parts is a fairly simple plumbing work, which any experienced master can handle.

The final element of the crossbow is the line dropper. It can be ground out of sheet metal. The finished plate is fixed to the stem plug with a few screws. After winding on the arrow to the flies in the front of the weapon, a tench is attached and placed under the ejector. When the shot is fired, the rope comes out from under the plate and begins to unwind after the outgoing arrow.

In the end, it remains only to deal with the crossbow firing. Then you can go directly to the defeat of submarine targets of medium and large size at a distance of about 3 meters.

Related news

How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing How to make a crossbow for spearfishing